- Stock: In Stock
- Brand: Luminex
- Product Code: 18181
Here is a Bio-Rad Luminex 200 Suspension Array Analyzer w/ Bio-Plex Manager 6.1
Made by Luminex, rebranded by Bio-Rad. This is a rebranded Luminex 200, this is not a Luminex 100
This Bio-Rad Luminex 200 Suspension Array Analyzer is in good working order.
The system is flushed with DI water after testing to ensure no clogging of the fluidics during storage.
Bottles and hoses may differ in appearance as they were borrowed from a separate listing.
New bottles and hoses have been ordered and their pictures will be added to this listing soon.
Please see the exact video and photos below.
Testing we performed:
The Bio-Rad Luminex 200 Suspension Array Analyzer passed all tests and was found to be fully functional:
Tested operation of software communication: PASSED
Tested operation of pneumatic pump and set air pressures to specification: PASSED
Tested operation of Probe and Probe actuator: PASSED
Tested operation of SD sheath fluid module: PASSED
Tested operation sheath fluid valves in system: PASSED
Tested operation of XYP Microplate stage: PASSED
Performed Calibration procedure in LX100 software and Bioplex Manager (Cal1/Cal2): PASSED (see attached screen shot)
Performed Validation procedure in LX100 software (Con1/Con2): PASSED (see attached screen shot)
Performed all cleaning and flushing protocols (Prime, Wash, Sanitize, Alcohol Flush, Soak): PASSED
By performing the Calibration procedure and getting a passing result verified that all the tested subsystems are operating together as they are designed.
In order to pull the calibration beads from the Test plate requires proper operation of the XYP Stage, Probe, Probe flow control valve, Probe actuator and operation of the syringe pump and it's valving as well.
Then for the calibration beads to be put through the flow cell requires the valving to switch over to the flow cell so the syringe pump can move the sample into the stream of sheath fluid.
The pressures and the fluidics need to be operating in the proper ranges so that the calibration beads do not flow too fast or too slow through the flow cell.
Then the lasers need to be aligned well enough with the flow cell that the beads can fluores at the right time to be seen by the detectors.
Then the detectors need to be operating properly to receive the fluorescent light and convert it to an electrical signal to be processed by the system and the software on the computer to provide a Passed calibration result.
Based on our tests we are certain this Bio-Rad Luminex 200 Suspension Array Analyzer is operating as it is designed at the time of testing.
System consists of:
Bio-Plex 200 System
XYP Microplate Stage
Bio-Plex HTF System (Luminex SD)
Sheath Delivery system tan air hose
Sheath Delivery system blue sheath fluid out hose
Sheath Fluid Bottle w/two attached hoses
Waste Bottle w/one attached hose
Probe height adjustment set
Bio-Plex MCV Plate IV
Metal 96-Well Microplate
Dell Latitude i5 running Bio-Plex Manager software ver6.1 w/ Dongle and Luminex100 IS software ver2.3
Communication and power cables.
Configuration and Setup:
Number of Lasers: 2
Laser Type: Reporter Laser 532nm and Classification Laser 63 nm
System checks for type of bead and if bead has analytes attached to it
Sample Handling: system uses 96 well-plates
Sample Volume: 20-200uL
First we go up to Bio-Rad Luminex 200 Suspension Array Analyzer. Going around the system to the back and close up of the tags on the Bio-Rad Luminex 200 Suspension Array Analyzer, XYP module and HFT module.
Coming all the way around to the front of the Bio-Rad Luminex 200 Suspension Array Analyzer again and showing the Bio-Plex software eject command for the XYP microplate stage with the Bio-Plex MCV Plat IV on it.
Run a wash command watch the probe sample the distilled water and watch the syringe actuate. Shows close up of software version and instrument information tabs with current calibration.
Luminex 200 Analyzer Datasheet: https://drive.google.com/file/d/0Bz5srQzgsa6uMG5lTWY2MUtMWXM/view?usp=sharing
Luminex XYP Datasheet: https://drive.google.com/file/d/0Bz5srQzgsa6uQjJSazI5NGVmMkU/view?usp=sharing
Luminex SD Datasheet: https://drive.google.com/file/d/0Bz5srQzgsa6uazI1VmdNQ0lrRkk/view?usp=sharing
This will ship via freight. Please contact us with your zip code to obtain shipping quote.
Please do not hesitate to contact us if you have any questions.
Here we are showing you our standard packing process
1. All items are different, but they all follow the same principle when packaging.
2. Start with a well-constructed crate
A well-constructed crate would consist of 1/2” to 5/8” Plywood with framing. We generally purchase our crates from a third party who specializes in custom crates.
3. You always want the Instrument to not be directly on the wood deck of the crate. This is done by placing it on foam, inside of the crate. We use 2” 1.7 lb. density foam which works great. It provides cushioning and enough firmness to support the Instrument.
4. The next step is to make sure there is nothing on the deck of the Instrument and the Head/ Arm is secured. In some cases there will be multiple arms to secure but for this example there is only one. The reason for this is so there is no free movement during transit which could cause serious damage to the Instrument.
5. The next step is to make sure your Instrument is covered in either a pallet bag or shrink wrap so no dust or foreign object will get into the crate.
6. The next step is to secure the instrument inside the crate by bracing. We use a method of 2x4’s which have 1” foam shrink wrapped to them so no piece of wood touches the actual instrument.
7. Final step is to photograph everything inside the crate and then seal it with screws.
All equipment warranty request must have a support case opened within the 60-day Domestic USA and 30-day International warranty period.
To open a support case, please send an email to firstname.lastname@example.org or call (508)974-4896.
Please provide your name, contact information, quotation/invoice number and a brief description of the issue that you are experiencing.
Phone and/or Email support will be provided prior to scheduling a return.
Please see the link below for our detailed warranty statement.
Customers must retain all original shipping materials during the warranty period.